Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Gate Installation in Wylie: What to Know First
Linear gate installation in Wylie typically runs from $1,800 to $6,500 depending on the gate’s size, the operator model, and how much of the existing framework can be reused. Most Linear systems we install for homeowners in Wylie are completed within three to seven days of the initial site visit, and every job is quoted in writing before work begins. We are an independent Linear service provider, not a factory-authorized dealer - which means we recommend what actually fits your driveway, not what a brand agreement tells us to push.
This page is for homeowners in Wylie who either have a Linear opener and need a new gate hung on it, or want both a new gate and a Linear operator installed as a complete system. If you’re in that spot, call (432) 249-5492 and we’ll schedule a free site evaluation. Victor Salinas and the crew have been putting gates on Wylie driveways long enough to know which questions to ask before we ever touch a post hole.
How Linear Products Fail - and How We Fix Them
Linear operators have a reputation for being workhorses, but they fail in predictable ways. The failures we see in Wylie are almost always installation-related or age-related, not factory defects. What matters is knowing which one you’re dealing with before you start bolting things down.
- Linear actuator travel limits drifiting out of calibration. On the Linear LDO50 and LS050 swing-gate arms, the internal limit switches wear gradually. A gate that used to close flush now stops three inches short, or slams at the end of travel. Homeowners often assume the operator is dying. It usually isn’t. We reset travel limits, clean the limit contact points, and verify the arm geometry. More than half the “dead” Linear arms we see in Wylie just need this correction, not replacement.
- Capacitor failure in hot weather. The Linear APeX series and older LDO models use motor-start capacitors that degrade in sustained Texas heat. Symptoms: the gate hums but won’t move at all on a 100-degree afternoon, then works again at night. Since Wylie gets weeks of triple-digit afternoons, we replace the capacitor with a higher-temperature-rated unit and check the thermal overload on the motor, which is the real long-term threat. A cheap capacitor swap without that second check buys you one season, not ten.
- Broken hinge welds on gate leaves installed without a proper header adjustment. This isn’t a Linear problem per se, but Linear arms are strong enough to rip a poorly-welded hinge off a gate frame before the operator even registers a fault. We repair the weld, hang the gate level, and make sure the operator isn’t fighting the gate’s own weight. A gate that closes against its own misalignment destroys operators and hinges equally.
- Photo-eye misalignment on Linear swing systems. Linear’s safety eyes are mounted differently than LiftMaster or Ghost Controls, and installers who are used to those brands often mount them too narrow or at the wrong height. The gate reverses for no visible reason, or won’t move at all. We remount the eyes to Linear’s specified beam height and width for the local driveway slope, then verify the obstruction reversal twice. This is a ten-minute fix from someone who knows it is a mounting issue, and a week of frustration from someone who doesn’t.
- Burned transformer in older Linear models running on under-sized wire. Linear operators draw more current at startup than most homeowners realize. The factory assumes a certain wire gauge over the distance from breaker to gate. When the original installer ran 14-gauge wire 200 feet, the transformer works overtime until it burns out. We check supply voltage at the operator under load, and if the wire is under-sized, we tell you before we replace the transformer - otherwise the new transformer burns out the same way. That’s the kind of thing that doesn’t show up in Linear’s spec sheet.
Our Linear Gate Installation Process
Every Linear gate installation in Wylie follows the same six steps, whether we’re hanging a new gate on an existing arm or starting from bare posts. We don’t add surprises, and we don’t cut corners against the clock.
- 1
Site evaluation. Victor Salinas or a senior tech walks the driveway, measures gate weight, post spacing, hinge height, and the power situation at the operator pad. We’ll tell you on that first visit if your posts are worth keeping or if they need to be set again. If the concrete footer is cracked, you’ll know before you spend a dollar.
- 2
Written quote. You get a line-item price: gate material, operator, mounting hardware, electrical, concrete, and any access wiring. The price is agreed before a single bolt is turned. No “we’ll figure it out later” additions at the end.
- 3
Gate build and prep. If we’re welding a new driveway gate, it is built to the weight your Linear operator can actually handle. A beautiful gate that weighs four hundred pounds on an arm rated for three hundred is a failure waiting to happen. We never oversize a gate against the operator you own.
- 4
Installation. Posts set and plumb, gate hung and swung by hand before the operator is attached. We swing it one hundred times by hand before we ever connect the arm. If it doesn’t move freely without the operator, it won’t move freely with one. That’s the old blacksmith test, and it’s never failed us.
- 5
Operator mount and wiring. Linear arm mounted according to the model’s mount geometry, wire run sized for the distance, all connections in sealed boxes. We test the photo eyes, the auto-close timer, the reverse safety, and the manual release. We also make sure the release handle is actually accessible, because most installers bury it behind the gate leaf where no one can reach it.
- 6
Test and walkthrough. Ten open-close cycles with a stopped obstruction test at the end. We leave the old parts with you if you want them, we show you how to release the gate manually during a power outage, and we put the 90-Day Done Right Promise in writing before we pull out of the driveway.
What Linear Gate Installation Costs in Wylie
Linear gate installation in Wylie breaks down into five common scenarios. The numbers below are real ranges from jobs we’ve done in the area, not national averages pulled from a search engine:
- New single swing gate, new Linear LS050 arm, on existing posts: $2,400 to $4,100. This assumes the posts are solid and the electrical is already within 80 feet of the gate.
- New double swing gate, new Linear LS050 operator, both leaves hung and aligned: $4,200 to $6,500. Two-leaf gates increase the weld time and the alignment time significantly.
- Full slide gate system, Linear SL series operator, new track and rollers: $3,800 to $6,200. The steel and the track work are both considerable.
- Pedestrian gate with Linear PPO2000 arm, new gate and post: $1,800 to $3,100. A good option when the driveway gate is fine but the walk gate is swinging loose.
- Operator replacement only (existing gate is straight and balanced): $950 to $1,700 for a new Linear arm or ram, including calibration and safety checks.
The three things that move the price in Wylie are post condition, access for concrete work, and the type of soil at the property where we dig. Blackland prairie clay expands and shifts with the seasons, and a gate set without accounting for it will be out of plumb in two years. We deal with that reality up front. Call (432) 249-5492 for an exact quote on your Linear gate installation - estimates are free, and the number we give you is the number on the bill.
Why Wylie Homeowners Call Ironworks Gate Co. for Linear Work
We’ve been doing gate work in Wylie and across Collin County since 1984, and we plan to be here another forty years. That changes how we work. The guy who is going to disappear in two years doesn’t care if your gate sags next spring. We do, because you’ll see our truck at the diner off Ballard Avenue, and you’ll remember whose gate that was.
Every Linear gate installation we finish is covered by our written 90-Day Done Right Promise. If something isn’t right, we come back and make it right. No argument, no paperwork, no “that’s not covered.” It’s the Keystone Standard on every job we touch, and it’s been that way long enough that most of our work comes from neighbors calling neighbors.
We are trained on nine opener brands beyond Linear: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and the rest. So when we put a Linear system in, we’re not squinting at the manual. We already know the quirks, we already know where the wiring fails, and we already know which aftermarket parts are worth using and which ones belong in the scrap bin. And if you call at 2 a.m. because a gate won’t close, a live person answers. Not a voicemail.
FAQs
Yes. Linear’s gate operator products are currently manufactured and distributed through Nortek Control, and parts and new units remain available through established supply channels. We order from the same distribution network as other independent installers, and we keep common Linear parts in stock in our trucks because we service them often enough to justify it. If a specific Linear model has been discontinued, we’ll tell you that on the phone and tell you your options, including compatible current models or another brand that fits your existing gate better.
No, not with us. Installing a Linear operator on a gate does not void the gate’s steelwork warranty as long as the installation does not structurally alter the gate frame. What voids more warranties in Wylie than anything else is improper grounding and the use of non-compatible arms. We follow Linear’s installation specifications and photograph the completed mount so you have a record. If you bought a gate with an existing warranty, we can review the terms before we install and tell you exactly what’s covered and what isn’t. Call (432) 249-5492 and ask - this is the kind of question we answer all the time.
Yes. Most of the Linear installations we do in Wylie are retrofits on existing gates, whether they were welded by another gate company, a local ranch fabricator, or a previous owner who decided to try it himself. We evaluate the gate’s weight, hinge condition, and post stability before we mount anything. If the gate isn’t straight, we fix that first. If the gate is too heavy for a Linear arm, we’ll tell you before you spend money on the wrong part. This applies to all models: the LS050, LDO50, SL series, and the PPO line.
Most Linear operator installations are scheduled within a few days of the estimate, and the installation itself takes one visit - typically half a day for a single-arm job. New gate construction with a Linear system takes longer because the steel is built to order and the concrete has to cure. We’ll give you a specific timeline at the estimate, and we’ll be there when we say. If your gate is down and you need it closed for security, tell us when you call. We do emergency calls, and a live person answers the phone at every hour.
Both, and we’ll tell you which is going on your job before we order it. For circuit boards and control components, we use Linear OEM parts, because the board is the brain of the system and the savings on aftermarket electronics aren’t worth the callback. For capacitors, limit switches, and some mounting hardware, we use industrial-grade aftermarket parts that meet or exceed Linear’s original specifications, and often outlast the originals in Collin County heat. If you have a preference, say so. The price difference is on the written estimate, not buried in a line item.
Ready to get your Linear gate installed in Wylie? Call (432) 249-5492 for a free estimate. We’ll come out, look at your gate, look at your driveway, and give you a straight answer and a written price. No pressure, no surprises, no bill until you know the number. That’s how Victor Salinas has done it for decades, and that’s how we’ll do it for you.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Wylie and nearby areas.