Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Elite Gate Access Control in Wylie: What to Know First
Independent Elite gate access control service in Wylie typically runs $225 to $480 for keypad and receiver repairs, and most jobs are finished the same day we arrive. If your Elite keypad has gone dark or your remotes stopped opening the gate on Ballard Avenue or over in Woodbridge, we’ll diagnose it for a fair, upfront price before any work begins. This page is for Wylie homeowners who own an Elite gate operator or Elite access system and want a straight answer about what’s wrong and what it costs to set right.
Call (432) 249-5492 and a live person answers, day or night. Tell us what the gate is doing wrong, and we’ll tell you what it actually needs.
How Elite Products Fail - and How We Fix Them
Elite has built solid slide and swing gate operators for years. That said, every line has its weak points, and we see the same handful of failures repeat across Wylie driveways. Here are the five we run into most:
- Elite SL-3000 keypad going dead after a storm. This is the most common call we get from Wylie homeowners with Elite swing gates. The SL-3000’s control board sits in a housing that isn’t sealed well against North Texas wind-driven rain, and the keypad wiring terminals corrode over time. A dead keypad usually isn’t a bad keypad. It’s a corroded screw terminal on the board or a shorted wire at the gate hinge. We clean, re-terminate, and seal the connection, then test the keypad through ten full cycles before we leave.
- Remote controls that work half the time. Elite receivers in the PR-1 and PR-2 series are sensitive to mounting location. When a receiver is mounted inside a metal gate post or behind a thick stone column on a Wylie lot, the signal gets partially blocked. The gate opens from the driveway but not from the street, or only when the remote is within ten feet. The fix is usually repositioning the receiver antenna, not replacing the remote.
- Phone entry system that hums but won’t dial out. We see this on older Elite Telephone Entry systems wired into landlines that don’t exist anymore. A lot of Wylie homes moved to VoIP years ago, and the old entry system’s modem can’t negotiate with the new line. We convert these to cellular or internet-based access so the call still rings the house phone. No need to rip out a working Elite system when the wiring has just changed under it.
- Card reader beeping but not releasing the gate. On Elite card and proximity systems, the reader often works fine while the relay inside the operator fails. The owner hears a beep, assumes the card is bad, and orders replacements that still won’t open the gate. We bench-test the relay first. A $40 relay beats a $400 reader every time.
- Wylie heat cooking the access control transformer. Elite operators generate heat inside the cabinet, and a Texas July adds another thirty degrees on top of that. Transformers and small power supplies inside the operator cabinet age fast here. When a keypad and a card reader both stop working the same week, the transformer is usually gone. We replace it with a higher-temperature-rated unit so it holds through August.
Those are real failures, not worst-case guesses. Victor Salinas has repaired hundreds of Elite gates around Collin County, and he’d rather show you the bad terminal with a flashlight than sell you a part you don’t need.
Our Elite Gate Access Control Process
We keep the work simple and orderly. Here’s how a typical Elite access control job goes when you call us in Wylie:
- 1
You call, we answer. A live person takes your call 24 hours a day. We ask what the system is doing, when it started, and what Elite equipment you have.
- 2
We diagnose on site. A technician checks the control board, receiver, keypad, reader, wiring, and power supply. We find the actual fault before we quote a dollar figure.
- 3
You get an upfront price. The quote is settled before a single bolt is turned. No surprises on the bill, ever.
- 4
We fix it right. We use Elite OEM parts where they matter most, like control boards and safety inputs. For external items like keypad enclosures and remotes, we’ll recommend quality aftermarket options when they perform as well or better for less money, and we’ll tell you the trade-off plainly.
- 5
We test it hard. Every keypad, remote, card, and intercom gets cycled repeatedly. We open and close the gate from every access point until we’re satisfied it won’t call us back.
- 6
You get the 90-Day Done Right Promise. If anything we touched doesn’t hold up, we return and make it right. Written, no paperwork, no arguing.
What Elite Gate Access Control Costs in Wylie
Elite access control repair in Wylie usually lands between these ranges, depending on what’s actually failed:
- Keypad replacement or wiring repair: $225 to $420
- Receiver or antenna fix for remotes: $180 to $300
- Card reader repair (relay, power, or reader itself): $240 to $480
- Phone entry or intercom conversion to cellular: $350 to $650
- Full transformer and power supply replacement: $200 to $375
- Complete new keypad, receiver, and two remotes package: $550 to $850 installed
What moves the price is whether the control board survived. If water or lightning got to the board, the part alone can push the job higher. We’ll show you the failed part and explain the cost before you approve anything. Estimates are free. Call (432) 249-5492 and we’ll give you a square deal.
Why Wylie Homeowners Call Ironworks Gate Co. for Elite Work
We’ve been doing gate work since 1984, and we’re not going anywhere. Wylie homeowners keep our number because we show up when we say, diagnose before we quote, and stand behind every job with the 90-Day Done Right Promise. Our technicians are background-checked and uniformed, and they work on your gate the way they’d work on their own mother’s driveway.
Because we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, you’re not left stranded if you ever swap equipment or add a second operator. One call covers every brand on the property. And the K.E.Y.S. code never changes: Krafted right, Every time, Your home first, Standing behind it.
Call (432) 249-5492. A live person answers, and you’ll get a straight answer before you get a price.
FAQs
We’re an independent Elite service provider, not a manufacturer-authorized dealer. If your Elite system is under factory warranty, we can still diagnose the problem and tell you exactly what to take to Elite for a covered part. Many Wylie homeowners prefer to skip the warranty runaround and let us fix it outright with OEM parts at a fair price, which is always your call.
In most cases you need only the keypad or the keypad wiring. We test the board first. When the board is also damaged, we’ll show you the evidence and quote the least expensive reliable repair path, not the biggest invoice.
For a gate that won’t open at all, we treat it as an emergency and typically arrive the same day you call. For keypads that work intermittently or a remote that needs repositioning, we’ll schedule a time that works for you, usually within a day or two. Call (432) 249-5492 and we’ll tell you straight what the schedule looks like today.
Some Elite parts, especially control boards for older operators, can take a few days to source. We keep common Elite components in stock on our trucks, but when an odd board is needed, we’ll tell you the lead time honestly and offer a temporary solution if one exists while we wait.
Usually not. When the remote works but the keypad doesn’t, the problem is most often a broken wire or a corroded connection at the keypad itself, not the keypad’s electronics. We check the wiring all the way back to the board before recommending any replacement. It saves our Wylie customers a lot of money on parts they didn’t need.
Have a question we didn’t cover? Call (432) 249-5492 and ask us directly. We answer the phone.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Wylie and nearby areas.





Before
After
Before
After
Before
After